ProEFI ECU's

ProEFI Pro128 ECU
ProEFI

9100

ProEFI Pro128 ECU

Regular price $1,701.69
/
Shipping calculated at checkout.

0 in stock

The ProEFI Pro128 ECU holds the record for bang for the buck. From it’s environmental specs, more inputs and outputs than you’ll probably ever use, to being hands down, the most reliable ECU you’ll find on the market at ANY price!

PROCESSOR The Pro128 uses the superfast MPC565 56mhz Processor
OUTPUTS  
Injectors 12 Peak n Hold – with calibratable peak time. 6 – 6/2 amp, and 6 3/1 amp.
Coils 16 EST Ignition outputs
Low Side Outputs 10 total – 8-10 amp capable – 2-2 amp capable*
Tach The Tachometer will also display information such as current Rev limit setpoint, and current I-Boost setting based on input from the cruise stalk. 
High Current Bridges 3 channel sets – Used for Stepper motor control, or Electronic Throttle Control
Expansion module capable Versioin 5z and later firmwares allow this module to use CAN based Expansion modules for additional I/O
Main Relay Control Yes
INPUTS  
Analog Inputs 34* Fuel Pressure monitoring and feedback correction, Oil Pressure, Exhaust Backpressure Feedback and correction, fault management with each input
Digital Inputs 8 channels – Fully programmable pre configured
Can Channels 2 Channels
Cam Digital or VR
Crank Digital or VR
Speed Inputs 10 Additional Frequency inputs are available (Speed1, Speed2, And DG 1- 8) Can be used for Turbo Speed sensors, additional Wheel Speed, Frequency Mass Air, etc…
Battery Backup No – Not needed – Stored permanently!
Serial Connection Yes*****
RS485 Connection Yes*****
Internal Memory Limited to Fault logic
USB Direct Connection No
Laptop Connection USB
FEATURES  
Air measurement Mass air (both frequency or voltage), True Speed Density via map  or Throttle based V.E. APC based igntion timing , or Standard MAP based, even with Mass air!
Air Temp Yes
Alternator control Can control duty based alternators
AntiLag ProEFI’s State of the ART antilag is unmatched in the industry! The ECU automatically adjusts timing and fuel to precisely control boost while staging. You can even control below your base spring pressure!
Automated Starter Control The ProEFI can be setup to control the starter like a modern vehicle…once key cycle engagement and the computer will run the starter based on parameters that can be defined.
Boost Control Most comprehensive and Accurate Boost Control and Antilag on the market. Multiple control strategies.***
Cam Yes – Hall/VR capable
Converter Dump The Converter Dump feature allows you to control converter charge to stage with more rpm against a tighter converter.
Coolant Temp Yes
Crank Yes – Hall/VR capable
Cruise Control(Pit Limiter) Comprehensive Cruise Control (Pit limiting)
Drive By Wire Yes – Dual capable*
Drive Off Assist Drive Off limiters to help with light rotating mass and grabby clutches. This also is used for variable two step control, more throttle is more limit rpm!
Drivers Information Light (Shift Light) The Drivers information light allows the user to define when the light activates by rpm per gear, boost, vehicle speed, brake staging, and more. Makes the shift light intelligent to precisely control the driver based on Conditions
Fan Control Control multile fans with user defined temperature inputs (Coolant, Oil, trans, etc…) Also Control Pulse width Fan control modules directly for Pulse driven Fans.
Fault Management ProEFI introduced Fault management in to the aftermarket over 13 years ago, and to this day still has the ONLY comprehensive Fault management strategy on the market (See Fault management for further details)
Flex Fuel Capability Add a Flex fuel sensor, and the computer automatically adjusts fuel, timing, and boost based on Ethanol content! Blend Target A/F, Spark, Accel fuel, etc…  Multiple Failsafes!
Fuel Pump Control Stage up to 3 fuel pumps, as well as controlling Pulse width duty controlled Fuel pumps
High Cam lobe control Control high lift cam(V-Tec) activation based on several paramters
Idle Control Pulse Width, Stepper motor, and ETC (DBW) – Adaptive
Ignition Timing Maps Low and High Octane map with function blending or switch activated. Split ignition for rotaries. Fault management to default to low octane maps for safety.
Knock Channels 2 Programmable frequency and event with individual cylinder notification
Launch Control Comprehensive Launch Control Strategies to get the most powerful cars down the nastiest tracks!
MAF Sensor Yes – Frequency and Voltage
Map Sensor Yes – Unlimited Range
MIL (CEL) The Check engine light is tied to any fault or condition and is user defined on what will trigger this light. This strategy can be set to force a clear or hold fault conditions, as well as display codes via MIL flashing digits. (see Fault Manager for comprehensive descriptions its capability).
Nitrous Control 4 stages progressive multiple event trigger control range. V.E. based fueling****
Rev Limiters Multiple – Burnout, Stage, TwoStep, Strain Gauge, Launch Control, Traction Control, and Rolling Antilag (True RPM capture at ANY Speed) All tied to separate boost targets!
Rolling AntiLag Control Speed based capture (no preset rpm or speed…press it and go)
Staged Injection ProEFI’s State of the Art Staged injection control makes it SUPER simple for the user to setup staged injection with no tuning needed. You can even stage in from pump fuel to straight methanol based on engine load!
TPS Yes – Adaptive
Traction Control Differential Wheel Speed, Driveshaft Speed, Accelerometer input for lateral power reduction, and more Multiple control strategies.***
Trans Brake Staging Control Controls the final staging to the second bulb via trans brake ‘bump’ in via trans temp and duty cycle for SMOOTH staging.
Transmission Control Comprehensive Transmission Control over any switch Logic solenoid to shift (no linnear trans solenoids) such as 4l60/80, A340 toyota, etc… Converter lockup control with min/max gears and rpm windows for smooth engagement. Full line pressure control, monitor converter slip with no additional Sensors (ECU automatically calculates this). Sequential Gearbox control for drag racing (control the aspects of each gear change based on multiple parameters).
Valet Modes Two Stages – Tied to Fault management – Power Reduction, Speed limited etc.. No laptop connection required to active or deactivate, calibratable procedure
Variable Cam Yes 2 cam capable
Wideband O2 2 Built in UEGO controllers (Inputs for External wideband capable)
Cart
ProEFI Pro112 ECU
ProEFI

9120

ProEFI Pro112 ECU

Regular price $1,350.00
/
Shipping calculated at checkout.

0 in stock

The ProEFI Pro112 ECU is the most economical, robust ECU on the market with tons of processing power, plenty of input monitoring and output to handle most builds.

Processor The Pro112 uses the industry leading superfast MPC5554 80mhz Processor
Injectors 8 Saturated Injector Drivers (peak and hold injectors must use a resistor pack on this ECU)
Coils 8
TPS Yes – Adaptive
Coolant Temp Yes
Air Temp Yes
Map Sensor Yes – Unlimited Range
MAF Sensor Yes – Frequency and Voltage
Idle Control Pulse Width and Stepper motor – Adaptive
Wideband O2 Uses CAN Based UEGO Control (External capable)
Cam Yes – Hall/Digital Only VR Cam Sensors must use converter box Part #9033
Crank Yes – Hall/VR capable
Variable Cam Yes 4 cam capable
Knock Channels 2 Programmable frequency and event with individual cylinder notification
Flex Fuel Capability Add a Flex fuel sensor, and the computer automatically adjusts fuel, timing, and boost based on Ethanol content! Multiple Failsafes!
Nitrous Control 4 stages multiple event trigger control range. V.E. based fueling****
Boost Control Most comprehensive and easy to use Antilag on the market bar none! Change your target with no re-tuning, set targets below spring pressure…no problem! Multiple control strategies.***
Rolling AntiLag Control Speed based capture (no preset rpm or speed…press it and go)
Rev Limiters Multiple – Burnout, Stage, TwoStep, Rolling Antilag (True RPM capture at ANY Speed) All tied to separate boost targets!
Traction Control Multiple control strategies, most advanced traction control system on the market.***
Launch Control Comprehensive Launch Control Strategies to get the most powerful cars down the nastiest tracks!
Valet Modes Two Stages – Tied to Fault management – Power Reduction, Speed limited etc.. No laptop connection required to active or deactivate, calibratable procedure
Drive Off Assist Drive Off limiters to help with light rotating mass and grabby clutches
Fuel Pump Control Yes, multiple staged pumps and pulse driven pumps*
Analog Inputs 34* Fuel Pressure monitoring and feedback correction, Oil Pressure, Exhaust Backpressure Feedback and correction, and much more.
Low Side Outputs 14 total – 4-7amp capable – 6-700ma capable, 2 1amp capable, 2 350ma capable, 1 100ma capable. 4 of these are PW capable (LS2, LS8, LS9, LS10)*
Tach Yes – Software configurable
Digital Inputs 3 channels (Not including Cam/Crank inputs)- Fully programmable pre configured
High Current Bridges 2 channel sets – Used for Stepper motor control, or Electronic Throttle Control
Drive By Wire Yes – Dual capable*
Fault Coding Safety Yes**
MIL (CEL) Yes – Malfunction indicator with fault codes
Main Relay Control Yes
5v Ref 2 locations
Sensor Grounds 2 locations
Key Switch Power Yes
Permanent Power Yes
Battery Backup No – Not needed – Stored permanently!
Chassis Ground 3 Locations
Can Channels 3 Channels
RS485 Connection Yes*****
Internal Memory Limited to Fault logic
USB Direct Connection No
Laptop Connection USB


Cart
ProEFI Pro70 ECU
ProEFI Pro70 ECU
ProEFI

9160

ProEFI Pro70 ECU

Regular price $908.61
/
Shipping calculated at checkout.

0 in stock

Pro70 Specs: Pro70e Specs:
   
 80mz Processor  80mz Processor
 Environmental – Meets J1113  Environmental – Meets J1113 
Voltage 8v to 32v Operating Range Voltage 8v to 32v Operating Range
25 Inputs/26 Outputs 25 Inputs/26 Outputs
Crank Input VR/Digital Crank Input VR/Digital
CAM Input Digital (up to 2 cams) 1 CAM Input Digital
Up to 19 Analog inputs 18 Analog Input
Up to 5 Digital Inputs Up to 5 Digital Inputs
1 Frequency input  1 Frequency input 
2 Knock Sensors 2 Knock Sensors
4 Peak and Hold Injectors + 2 Saturated Injectors [Total of 6 Injectors] 4 (7amp) Peak and Hold Injectors
6 EST Ignition Outputs 6 EST Ignition Outputs
9 Low Side Outputs 7 Low Side Outputs
1 H-Bridge 1 H-Bridge
2 CAN 2.0 Channels 2 CAN 2.0 Channels
1 Speed Input  1 LSU 4.9 or NTK Wideband – No Speed Input
4 Switch Inputs (non-frequency) 4 Switch Inputs (non-frequency)
3 Lamps (low current output) 3 Lamps (low current output)
Cart
ProEFI ProPDM ECU
ProEFI

9165

ProEFI ProPDM ECU

Regular price $837.18
/
Shipping calculated at checkout.

0 in stock

Operating Voltage

  • 12v/24v nominal

  • Reverse polarity protection

Operating Current

  • Total: 70 AMP, simultaneous active outputs

Input

  • 12 digital tri-state [high-side, low-side, open] for external switch to active functions calibratable in the ProEFI ECU when not using CAN trigger functionality.
  • 2 analog [Resistive] Broadcast to the ProEFI ECU through CAN and usable as an analog input for any function.
  • 6 analog [0-5 VDC] Broadcast to the ProEFI ECU through CAN and usable as an analog input for any function.

      Output

  • 12 digital high current [15 AMP max each, 70 AMP total] +12v High Side Outputs

* Can be configured as PWM operation 

Calibratable Fuse Settings

  • 5 AMP to 15 AMP
  • Auto Resetting Fuses

CAN Interface:   CAN 2.0B

Dimensions:       245 x 140 x 50 mm

Weight:               2 lbs

Water sealed Connectors

  • 3 x 12 pin [ J3, J4, J5]
  • 1 x 2 pin [ J6 ]
  • J1- Ground – 8 gauge
  • J2- V batt – 8 gauge

Note: A proper circuit breaker should be used on the main power feed capable of supporting the total system draw.

Environmental Specs

  • Operating Specs -40*F to +185*F
  • Storage Specs -40*F to +275*F
  • Environmental Sealing IP 66 and 67
  • Shock 30 G, 3 cycles
  • Vibration 5 – 25 G, 50 – 2000 Hz, 72 hrs/axis

* ONLY Compatible with ProEFI Systems

Cart